batocera.linux 5.25 with nvidia-legacy drivers (390.xx) - Discontinued

poke · 2019-01-25T12:37:26+00:00

Community provided build for 5.27 with nvidia-legacy: https://batocera.org/users/alexxandrefs/5.27-nvidia-legacy/ I’m looking for someone to maintain this c...

xerxes

...for two reasons:

It seems that the legacy drivers are a little bit better: Gamecube F-Zero runs almost flawless now and PS2 Silpheed without stuttering (on a Intel i5, 8GB RAM).

I am going to buy a GT 1030, so I will need the legacy driver in the future and I wanted to test the drivers before. But the fact that updates will not work makes me think about this upgrade - will there be legacy driver in the future? At least as "new installments / images"?

poke

xerxes did you enable the nvidia-drivers in batocera before? vanilla ships with nouveau and nvidia-drivers. By default, you get nouveau. You have to enable it following the same procedure (edit recalbox-boot.conf).

This thread has an old version of nvidia-drivers (390.xx or nvidia-driver-legacy).

xerxes

...yes, I enabled the nvidia driver in the recalbox-boot.conf. As far as I understand are the "official" images of batocera shipped with open source drivers, and the custom built with proprietary drivers from nvidia!?
Like I wrote - the drivers of the custom build seens to work a little bit faster: In Silpheed (PS2) for example I had few stuttering, this is gone now. I should test more games to verify...

poke

xerxes not exactly..

official images ship with open-source and the last nvidia proprietary version
my custom build ships with open source and the legacy nvidia proprietary drivers

If you card is supported, and yours is, you can enable nvidia-driver in the official image. Just edit recalbox-conf.boot.

xerxes

poke Thanks for this information!

So I can go on with the official image. But how can I find out that the GT 1030 will be supported? The list here: https://www.nvidia.com/Download/driverResults.aspx/137276/en-us seems to be valid only for the legacy driver - or did I get this wrong?

Thanks and regards
Michael

poke

xerxes Compatibility list for 415.27: https://www.nvidia.com/Download/driverResults.aspx/141847/en-us

GameCast

i have GTX 1050 ti 4gb and works greate 😉

poke

GameCast you can use the standard batocera image with a 1050. The new and shine nvidia-driver is available. This custom build is older gpus (series 5 and 4). Your card is a series 10. Just upgrade to 5.20 and be happy.

You are the second to use the legacy branch unnecessarily. I guess I need to put a warning in the first post...

KaratsuFr

poke Big Thanks
so batocera standard 5.19 without driver was not usable for
Saturn (test virtua fighter 2)
Gamecube (test mario kart)
Wii (test mario kart)
PS2 (test DBZ Budokai 3)
most of the rest was ok
now on my Core2Duo 3Ghz 4Go Ram and GT560Ti
saturn / Gamecube / wii run fullspeed
ps2 almost : cpu limit

got issue with multiple output video and need to connect to DVI 1 but after that all good
(if not on good DVI was having high CPU usage and no nv accelaration)

would be very happy to have this version by default

GameCast

poke i just want confirm the batocera versions 5.19 and 5.20 are working greate whit gtx 1050 .. not necesary to edit recalbox.cfg #nvidia to nvidia ..

poke

GameCast yes, batocera will work ok using the default drivers with 2D emulators. Performance of 3D, like wii and ps2, is much better with nvidia proprietary drivers.

GameCast

poke i´ve tested the 2 ways whit nvidia and without nvidia , and just got some diferences emulation on 3ds cores. with nvidia configured 3ds runs smootly on some games .
ps2 wii and game cube it runs over open GL dont see some diferences on this emulation systems .

poke

GameCast OpenGL stack on nvidia drivers is better than nouveau/gallium. Anyway, if you are happy with open source drivers, good.

KaratsuFr

GameCast - your setup seems to be over powered that's why you don't see any diff with or without nvidia drivers 🙂

during your test have you activate FPS to be sure you are not running under fps sometime ?

the most consumming emulator so far is PS2 or 3DS ..

poke overall most user won't see the diff if they have good any configuration but having the most of an hardware help quite a lot and if ps3 emu or wii u emu are going to batocera i'm sure that this will make a diff

tris20

When I edited the boot config file. With felting the # the I only got I black screen. I hear the menu sound but nothing else.

poke

tris20 gpu model? Which image? Legacy or batocera default?

GameCast

poke i see not issues on open source drivers .

poke

GameCast did you try to set internal wii/gc resolution to 1080p? It is doable with your 1050.

tris20

poke

gt540m ( is listed in the link from above ) videocard with an i7 cpu and 16 gb ram
this image from above so legacy?

GameCast

poke first one , i dont like wii emulation on batocera cause controls isues, but gamecube yes is working very good 1080 resolution .
but i´ve tried some wii isos on the 5.19 was working greate at 1080 .

i have 16 gb ram and fx8350 processor 4.0 ghz . works all greate offcoarse respecting the compatibilities list .

for example wii call of dutty black oops was running very poor instead tale of symphonia was working like a charm .

poke

GameCast 1080p internal emulator resolution. Not external/video resolution. You have to set it manually in dolphin ui. Otherwise default interna resolution is 480p.

poke

tris20 yes, the image above is nvidia-legacy.